![]() ![]() To put things into perspective I have included a table below comparing the different scenarios together with reads of the sensor exposed to radiation from a controlled x-ray source. Our goal is to find these issues and address them before they become problematic. At no time any of the tubes tested presented any abnormal sensor reads indicating the presence of X-rays. there's no such thing as a free tan while retro gaming. Toshiba A68 CRT (NANAO MS9) on a New Astro City cab ![]() Initially the X-ray sensor is left to warm up for a good 10 minutes to obtain constant ambient reads. X-ray activity is sampled during 180 seconds during each run, then compared against ambient readings (tube turned off). You can get an X-Ray or an MRI right in clinic as well as therapy, bracing, guided injection procedures. In front of each tube an X-ray sensor is placed at different distances: 3cm, 30cm, 60cm. 3580 Arcade Street, Vadnais Heights, MN 55127. I believe these models are also commonly found among the gaming community and they should be somehow representative. deSa of Salmon Orthodontics are your Batavia, Hornell, Wellsville, Arcade, Perry, and Attica, NY orthodontists providing. My setup involved testing three tubes in my collection used from time to time for testing arcade pcbs, retro consoles, as well as micro computers. I am thinking I should be measuring the voltage going into the flyback at this point? I am thinking if the voltage is low going into the flyback then it would naturally be low coming back out of the flyback? It looks like power goes into pin 3 on the flyback per the schematic.Motivated by this discussion at UKVAC I decided to run a little experiment to find out if your typical gaming CRT leaks any measurable X-rays. I assume this means that my new flyback is good? (That or both flybacks are suffering from the same problem anyway?) (The old one was working just fine before, just changed it as preventative / shotgun) I then hooked everything up and measured at TP33. I see your comment about a bad new flyback, so I desoldered the new one and put the old one back on. It pretty clearly says this should be 200V. I sat and looked at the schematic for a while. Voltage is approximately the same at TP33. I then measured voltage at TP33 so see if perhaps it was R235 causing havoc. Serving pizza bagel & virtual concert combo meals throughout the pandemic. As a point of data, the screen looks identical with R40 removed from the circuit. Arcade, bar, and all-ages music venue Cudahy, WI. X-Ray Arcade Cudahy, WI Tickets & Info Fri Flatfoot 56 X-Ray Arcade Cudahy, WI Tickets & Info All concerts at X-Ray Arcade More Upcoming Conjurer Concerts Thu. Ironically, this corresponds to what my TP6 was previously. So I whipped out the multimeter and measured the voltage at R40. Hooked up the chassis, fired it up and no burning smells. Over the past year, the quartet has quickly built a following in the Chicago indie-music scene around their surf and garage/punk. The band's lineup features Marites Velasquez (bass), Sarah Braunstein (drums), Kyla Denham (synth) and Nick Barnett (guitar). I got a new R234 installed, and I removed R40. Ovef Ow is a 4-piece space surf rock band that formed in the spring of 2015. I am determined to get this thing working as long as you are willing to aim me places. Will update once I have something to update with. If not I guess I am going to end up ordering one from Mouser, but it really sucks to pay $5 shipping for a. Tomorrow - back to radio shack to see if they have "flame proof" 10 ohm resistors for R234. I've got the old one as well so I can swap it into the socket too if it acts weird with the new one. Since the monitor worked identically with the new resistor (at least for the 30 seconds I had it on before smelling burning resistor) I went ahead and socketed the LM1203 and installed the new LM1203. exhibition that includes a wide range of artifacts, ephemera, costumes, x-rays, massive window-walls, infographicsand a 1970s-style arcade game. The screen seemed to be the exact same though. R40 had about 160v DC on it with the new resistor, which is of course different that the 0v DC it previously had. I did decipher a few things before the burning smell became obvious. Hopefully it is! WTF happened I thought? So I started looking at the schematic and realized that this was something called a "flame proof" resistor, not a 1/2 watt. It appears the rest of the board is ok though. All-ages music venue, rad arcade, and stellar drinks hidden in Cudahy, WI. ![]() I started smelling something burning and quickly turned the monitor off. I installed a normal 1/2 watt 10 ohm into R234. So I learned a valuable lesson tonight: Blue resistor's are NOT just blue for no reason. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |